How To Winch Backwards like a Pro {Updated on May 2022}

The winch is an essential part, especially when you’re off-roading. You should always bring a winch with you when going off-road. You never know what’s in store for you. 

Your vehicle could become stuck at any time. A winch will come in handy at that point. However, this is not always the case. 

In some cases, you have to reverse the direction of your winch. As a result, it’s best not to leave other options open. That is why you should learn to winch backward.

This article will go over the methods and specific steps on “How to Winch Backwards”. So, let’s get this party started.

How to Winch Backwards

There are two methods for winching backward in general. The first is the most straightforward. 

On the other hand, the next one maybe a little more difficult. We will go over both methods. You can choose anyone who makes you feel at ease.

Also check: Some of the best winches

#1. Directly Winching

Locate a secure anchoring point that can withstand the weight of winching your vehicle out.

The disengage lever is located on the opposite side of the winch. The lever should be labeled “free spool” and “disengage.”

Turn the lever to the disengaged position to manually pull out the winch cable.

Pull the winch cable away from the winch, but not so far that it causes unnecessary slack.

Take your winch cable and run it underneath the vehicle. Ensure there are no places under your car where the cable could be damaged.

Your winch should also have an “Engage” label. Turn the lever to the “Engage” position to prevent more winch cables from escaping.

Winch your way back to the anchoring point using the remote. When this occurs, the winch cable is slowly drawn towards the winch, causing it to tighten. Make sure to follow the steps in the correct order.

#2 Snatch Blocks Winching

As in the previous one, you must find the anchoring points in this method. This time, you must identify three anchoring points. 

Two anchoring points will be located in the rear of your vehicle, with the third anchoring point located in the front. 

Obviously, the anchoring point you choose must be stable enough to support the weight of your vehicle for it to be able to pull your vehicle out. Three is a good number to use as your anchoring point.

After locating the anchoring point, disengage your winch lever to release the winch cable. Your winch’s lever is located on the outside. 

Along with the lever, a label will say “free spool” and “disengage.” You must move the lever to the disengaged position. After turning the lever, you will manually pull your winch cable.

Your next task is to remove the winching cable. So, simply pull out your winch cable. You should not pull too hard to avoid slack. Try to get the exact amount you require.

Wrap a tree trunk protector around your anchoring point now. The tree trunk protector is typically a nylon strap with a loop at the end. 

Each of the three anchor points must have its own trunk protector. Because the snatch blocks will be held in place by this tree trunk protector.

The D-shackle must then be secured with the three straps.

Then, using the D-shackle, attach two of the three snatch blocks. So, connect the snatch block to the D-shackles on your tree trunk protector. 

As I instructed you to attach two snatch blocks, you should do so except the last anchoring point, which is located on the front side of your vehicle.

Then, in the previous step, hook the last snatch block to the rear of your vehicle. You must locate a suitable location for attaching your snatch block to the back of your vehicle.

You must now wrap the cable around the snatch blocks. This is done because your pulley block casing may open to allow you to turn the screw on its side. 

Wrap your winch cable around three pulleys first, then close the casing.

After that, connect the winch cable hook to the third anchoring point. Remember that you previously attached a D-shackle to your third anchoring point. 

So, using the D-shackle that is already attached to your third anchoring point, connect the winch cable to it.

The next step is to turn the lever to engage it. On your winch, look for a label that says “engage.”

To engage, you must turn your lever. As a result, your winch cable will no longer be able to come out.

You have completed the setting process and can now begin winching. When you begin winching, you will notice that your vehicle is driving backward.

Also check: How To Use A Block And Tackle With A Winch

Conclusion

Hope you learned How to Winch Backwards in this article.

This is one of the two methods for winching yourself backward, and it can come in handy if you get stuck. Hope this article helped you.

Check our other winch-based articles, you might find them helpful.

Note: As an Amazon Associate, I earn commission from qualifying purchases at no cost to you.

Photo of author

CEO & Head Author

Author

Edward

Edward is an Off-Road enthusiast who wants to help other enthusiasts use the power of information to find, compare and buy the winch product that is right for them.

Leave a Comment